Sidan 2 av 2 FörstaFörsta 12
Resultat 16 till 30 av 30
  1. #16
    80mm Njutning
    Namn
    Jens Sundkvist
    Reg.datum
    dec 2005
    Ort
    hofors
    Inlägg
    301
    looks great!
    Tuned and built by PPF
    10.01@233km/h 402m
    Bygger nytt för 2012

  2. #17
    Egenföretagare
    Namn
    Roger Persson
    Reg.datum
    sep 2003
    Ort
    Broby Skåne
    Inlägg
    414
    RAW! Just fucking raw!
    Få bra bilder till bra pris. www.rp-photography.se <- Sidan roger@rp-photography.se <- Mailen raggeno1@hotmail.com <- MSN'en

  3. #18
    Registered User
    Namn
    Helmut Gutting
    Reg.datum
    mar 2010
    Ort
    Germany, Bavaria
    Inlägg
    14
    Hi

    Friday was the big day, the engine managment arrvived, it come´s from MME which is a german producer of engine managments. The MME ECU 481 run´s on the quickest VW´s in germany, so we are excitedly, because it´s the first install on a BMW =)
    Because of the MME we changed the fuel pump from Aeromotive to Fuelab, because the pump can be pressure regulated by engine speed. And because of that we had to change the inlet line from the tank to the pump up to 18mm(15mm inner diameter) and also the flow line in the same diameter.

    The most of the plumbing is also done

    here some pictures:
    Bifogade bilder Bifogade bilder          
    heturbo.net: what happens in anywhere ;-)

  4. #19
    Kör BMW... GSXs avatar
    Namn
    Janne H
    Reg.datum
    aug 2002
    Ort
    Stockholm
    Jobb
    IT Tekniker
    Inlägg
    269
    Very interesting project! Keep the pictures coming, and we want a movie when it's done! ;-)

  5. #20
    wescrape Viper89s avatar
    Namn
    Joakim Skagerlind
    Reg.datum
    jun 2002
    Ort
    Uppsala
    Jobb
    JSF
    Inlägg
    3 569
    Sick project!!!
    Mvh Joakim Skagerlind - 0760 - 940 776
    http://www.garaget.org/Viper89
    E28 545 (951hp@1,8bar) || E39 530D || E36 318 TDS Compact
    Only Beemers with a snail on...

  6. #21
    Turbo user mattssons avatar
    Namn
    Mattsson D
    Reg.datum
    aug 2001
    Ort
    Ryd
    Jobb
    Scania 144 460
    Inlägg
    353
    nice
    a tip off the day is to put som alu rods throu the intake plenum as reinforcment if yo havent don this allredy
    Mappning av Bosch styrsystem
    http://www.mappa.nu

  7. #22
     User tungfotads avatar
    Namn
    Manuel D
    Reg.datum
    okt 2006
    Ort
    Strawtown
    Inlägg
    528
    Sick is the word! Looking forward to the next update, so keep 'em coming
    ///M3an | Jeremy Clarkson - "M3 drivers have no friends"

  8. #23
    Turbo addict
    Namn
    Mikael R
    Reg.datum
    sep 2003
    Ort
    Köping
    Jobb
    Hertig
    Inlägg
    4 643
    Just curious, why did you abandon the bi-turbo setup?
    2000 Mitsubishi Lancer Evolution VI T.M.E@600hp

  9. #24
    Registered User
    Namn
    Helmut Gutting
    Reg.datum
    mar 2010
    Ort
    Germany, Bavaria
    Inlägg
    14
    thank you guy´s =)

    @mattsson

    I think it would work. Because it´s bend. And the sheet metal is weldet from both side´s. So I hope it works. Or do you definitely know that it don´t work?

    @fanimej

    The bi-turbo setup was nice but we don´t get enough power =)
    Bifogade bilder Bifogade bilder        
    heturbo.net: what happens in anywhere ;-)

  10. #25
    Turbo user mattssons avatar
    Namn
    Mattsson D
    Reg.datum
    aug 2001
    Ort
    Ryd
    Jobb
    Scania 144 460
    Inlägg
    353
    Depends on boost pressure but its not acualy the welds that fails its big flat surface... that often become a ballon....
    i cant say it wont work but i hawe seen many exampels running high boost that has problems and needing to reinforce
    Mappning av Bosch styrsystem
    http://www.mappa.nu

  11. #26
    Registered User
    Namn
    Henrik R
    Reg.datum
    sep 2004
    Ort
    Göteborg
    Inlägg
    3 763
    Crazy project, but so cool!

    Keep it up!
    Mvh Ruergård

  12. #27
    Registered User
    Namn
    Helmut Gutting
    Reg.datum
    mar 2010
    Ort
    Germany, Bavaria
    Inlägg
    14
    @ mattsson

    that´s also my apprehension with that much boost. And what you say is a weak point, you have seen some blown manifolds, me not So I will reconsider my decision. Thank´s =)
    heturbo.net: what happens in anywhere ;-)

  13. #28
    Registered User
    Namn
    Helmut Gutting
    Reg.datum
    mar 2010
    Ort
    Germany, Bavaria
    Inlägg
    14
    After a few weeks of thinking and building new parts: a small update =)
    Some sensors have found her way under the hood

    If anybody of you is interested in the CNC milled Pump holders, feel free to contact me.
    Bifogade bilder Bifogade bilder           
    heturbo.net: what happens in anywhere ;-)

  14. #29
    Förargelseväckandekörstil Nisse Järnets avatar
    Namn
    Nisse J
    Reg.datum
    dec 2001
    Ort
    Stockholm/Norrort
    Jobb
    Nätverkstekniker
    Inlägg
    7 917
    Looking good!
    3:a USR 2007
    3:a Team Insane Racing 2007
    3:a Nattracet Cup 2008
    Finalist Nattracet Cup 2009
    4:a Norr vs Söder 2009
    http://www.pure-pf.com
    http://www.nordicmilitarytraining.se

  15. #30
    Registered User
    Namn
    Helmut Gutting
    Reg.datum
    mar 2010
    Ort
    Germany, Bavaria
    Inlägg
    14
    Hi

    I have seen that some pic´s are missing here =)

    Here some pic´s about what´s happend















    A e28 210mm differential







    and the mounted Fuelab pump with filter



    So that´s for now
    heturbo.net: what happens in anywhere ;-)

Behörigheter för att posta

  • Du får inte posta nya ämnen
  • Du får inte posta svar
  • Du får inte posta bifogade filer
  • Du får inte redigera dina inlägg
  •  
Vill du annonsera ovan? Klicka här